flanges
英 [ˈflændʒɪz]
美 [ˈflændʒəz]
n. 凸缘; 法兰; (火车的)轮缘
flange的复数
柯林斯词典
- 凸缘;法兰
A flange is a projecting edge on an object. Its purpose is to strengthen the object or to connect it to another object.
双语例句
- The cast iron flanges minimize the need of pipe unions and fittings while offering ease of installation and maintenance.
铸铁法兰对管道活结和配件要求达到最小化，可提供简便的安装和保养。 - The contact surfaces of the outlet sprockets and camshaft flanges must be completely free of oil and grease.
排气链轮和凸轮轴法兰的接触面必须完全没有机油和润滑脂。 - Other methods and products for flanges protection may be acceptable, subject to employer approval.
经业主批准，可接受用于法兰保护的其他方法和产品。 - The humanity design also includes the disassembly and installation system of column piston and flanges.
并附加了活塞及柱底法兰拆卸与安装系统，更加人性化。 - Rubber faced or mechanical flanges are not recommended.
建议不要使用橡胶表面或机械法兰。 - Flupac's advanced non welded piping technology is based around retained flanges, and pipe end preparation machines.
福尔湃克领先的管路连接技术是基于保持环和管端预制机器基础上的。 - The bolt hole pattern and outside diameter dimensions were adopted for plastic flanges manufactured in the U.
用于美国制造的塑料法兰上所采用的螺栓孔模式和外径尺寸。 - Valves should not be assembled to the flanges and then welded into the piping system.
不要把组装上法兰的阀门焊接到管道系统上。 - Provide steam rings for tube side inlet and outlet flanges.
管程的入口与出口法兰配备蒸汽环。 - Prime bonded body flanges in the marked areas and.
为标记区域和中的粘结车身法兰涂底漆。 - The ends have two flanges that allow you to easily depress the spring to install or remove.
两端有两个法兰盘，让您轻松地抑制弹簧安装或删除。 - Bolts are ground and flange holes are calibrated for perfect centering of the two flanges in respect of each other.
螺栓经过打磨，法兰螺栓孔也经过校准，实现了2个法兰相互之间的完美对中。 - The risers are attached by means of flanges, studs, and heat-resistant brass nuts.
该管的重视手段法兰，螺栓，耐热黄铜坚果。 - Fit five new O-rings on the connecting flanges.
在连接法兰上安装五个新的o形圈。 - Spiral wound gaskets for pipe flanges Ensure the ground clip is on spacer slot.
管法兰用缠绕式垫片应确保接地夹片在垫片槽上。 - Remove the old sleeve by bending the flanges at one end and withdrawing the sleeve from the other end.
要拆卸旧套管，要通过弯曲法兰的一端，然后将套管从另一端抽出来。 - Any blanking flanges, plugs, caps and desiccant bags shall be removed before connecting up the pipes.
译：任何闷板，塞子，帽子和干燥包将要在连接管路之前移走。 - Adjust windshield glass position until it is aligned with the flanges and adhesive.
调整挡风玻璃位置直至与凸缘和粘结剂对准。 - A cylinder with flanges on which tape may is wound.
有边盘的圆柱，其上可以绕带。 - When bolting to steel flanges, longer bolts or stud may be required.
如果是应用在钢法兰晌，可能需要更长的螺栓或双头螺栓。 - During fabrication slots for the stringers flanges were flame cut into box girders.
制造时，为安装纵梁翼缘，在箱型梁中用焰割法开槽口。 - Wafer-style held in place between two pipe flanges. Easy to install but cannot be used as isolation valve.
平板式（对夹式）：固定在两个管道法兰之间。安装容易，但是不能作为隔断阀使用。 - Technology: flange type of heating is heating pipe welding flanges from fixed.
工艺：法兰式加热管是由加热管与法兰焊接固定而成。 - All flanges shall be furnished in a heat-treated condition.
必须对所有法兰进行热处理。 - The profile seals must be fitted securely on the flanges, particularly in the bends.
必须将轮廓密封件牢固地安装到法兰上，尤其是在弯曲处。 - Flanges threaded for smaller pipe sizes, or flanges adapted for welding, are also available.
带螺纹的法兰也适用于较小管子的尺寸，或适宜焊接法兰。 - Insert intake air lines into the flanges on the turbocharger.
将进气管插入到涡轮增压器的法兰中。 - Dimensions and References – Pipe Threads, Flanges, and Pressure Conversion Factors.
尺寸和参数-管道螺纹，法兰，以及压力换算系数。 - When flanges are integral with fittings or valves, holes for bolts are drilled to straddle the center line.
1如果法兰与连接件或阀门构成一个整体，则螺栓孔钻在圆心线两侧。