mandrel

1. The centers must be aligned and the mandrel must be free of burrs.
   这些中心点必须排列成一行，并且保证心轴上没有毛刺的现象出现。
2. Check the position of the crankshaft using the measuring mandrel.
   用测量心轴检查曲轴位置。
3. Mount the workpiece onto a lubricated mandrel of the proper size by using an arbor press.
   通过利用杠杆式冲床将工件锚定在适当尺寸的润滑心轴上。
4. The base consists of a chassis and a mandrel, the mandrel which is matched with the positioning sleeve is installed on the center of the reticular chassis.
   底座由底盘和芯轴组成，网状底盘中心装有一与定位套匹配的芯轴。
5. Use a hammer and mandrel during assembly if necessary.
   必要时在装配期间使用锤子和芯轴。
6. Remove special tool centring mandrel.
   拆下专用工具定心芯轴。
7. Align piston and connecting rod again using the centring mandrel.
   使用定心心轴重新对齐活塞和连杆。
8. Design and Simulation of Assembled Camshaft's Mandrel Automatic Transportation System
   装配式凸轮轴芯轴自动上料系统的设计及仿真
9. Threaded mandrel's in high proper alignment request components lathe work application
   螺纹心轴在高同轴度要求零件车削加工中的应用
10. The manufacture and process techniques of the wrought Mo alloy piercing mandrel have been introduced.
    介绍了变形态钼合金穿管顶头的研制及其工艺技术。
11. To produce specialty tubing, this procedure uses a drawbench to pull tubing through a die and over a mandrel, allowing excellent control of the inside diameter and wall thickness.
    这一程序通过拔管机使管子经过钢型和心轴的拉制，这样管子的内径和壁厚精密度就能控制的很好。
12. The3-roll mandrel pipe mill is regarded as the most advanced seamless steel tube mill in the world.
    三辊连轧管机是当今世界上最先进的轧管机。
13. The structural design of molding mandrel of pyrophillite was improved.
    对叶块成型芯轴的结构进行了设计改进。
14. Hydraulic hob mandrel clamping.
    液压滚心轴夹紧。
15. After the mandrel is melted, a thin layer of alloy remains on the propellant surface.
    此心轴溶化之后，在推进剂表面上留有一薄层的合金。
16. The mandrel ( including flexible balls) is the key to improving the forming limit and forming precision in thin-walled tube NC bending process.
    薄壁管数控弯曲中带芯头的柔性芯模是提高薄壁管件成形极限和成形精度的关键因素。
17. Outer cladding metal nearby the fusion interface of roll mandrel experienced the process of solidification-fusion-re-solidification.
    辊芯熔合界面附近的外层金属先后经历了凝固、熔化、再凝固的过程。
18. In this article, analyse the reason of the mandrel can not use; introduce the project of alteration, and the maintenance measure for the mandrel.
    本文分析了芯轴不能正常使用的原因，并介绍了技术改造方案及维护措施。
19. To study the mechanism of production and regularities of distribution for residual stress in pipe drawing with fixed mandrel, the drawing process was investigated by elastic-plastic FEM.
    为了研究固定短芯棒拔管残余应力的产生机理和分布规律，采用弹塑性有限元法模拟拉拔过程，讨论模具形状参数、拉拔变形参数、摩擦条件对残余应力的影响。
20. Test mandrel must now be clamped in a vice.
    测试芯轴此时必须用老虎钳夹紧。
21. The centring mandrel remains in the eye of the connecting rod until the piston contacts the centring mandrel during fitting.
    在安装过程中，在活塞与定心心轴相接触之前，定心心轴一直保留在连杆孔中。
22. Remove crown wheel using a rubber hammer or aluminium mandrel.
    使用橡胶锤或铝芯轴拆下盆形齿轮。
23. Fit bearing cover using special tool removal mandrel.
    使用专用工具拆卸芯轴安装轴承盖。
24. It should just be possible to turn the measuring mandrel by hand.
    应刚好可以用手转动测量心轴。
25. Align piston connecting rod using the centring mandrel.
    使用定心心轴对齐活塞连杆。
26. The mandrel must be mounted between centers and a drive plate and lathe dog must be used.
    必须将心轴锚定在中心点和驱动板之间的位置，并且必须使用车床轧头。
27. Centring mandrel must be used.
    必须使用定心芯轴。
28. This paper, with an implementation example, describes the principle using magnetic detection to monitor the mandrel's breakage and axial wobble in a cold-rolling mill for steel seamless pipes.
    所介绍的芯棒监视器可以对无缝钢管冷轧机锥形芯棒的断裂和轴向窜动进行连续监视，由于它采用了非晶态合金制成的芯棒位移传感器，因而具有很高的灵敏度和反应速度。
29. Press the rear-wheel hub out using press-out mandrel.
    使用压出心轴压出后轮毂。
30. Design in the mandrel land and smoothing the deformation of rectangular tube drawing
    矩形管成品拉拔的芯头工作带设计与变形平滑化

noun

1. any of various rotating shafts that serve as axes for larger rotating parts

   Synonym:    spindlemandrilarbor