mandril

1. Application of Bus Loopy Absolute Encoder in Position Control System of Mandril Thrust Block
   总线式多圈绝对值编码器在顶杆小车位置控制系统中的应用
2. Obiective Test the relationship between the heating time of electrothermal vaporizing liquid and the residues of pyrethroid in mandril.
   目的测试电热蚊香液加热时间与芯棒中拟除虫菊酯残留量的关系。
3. Control Piston and Mandril Lift Measurement of Electronic Control Injector
   电控喷油器控制活塞和挺杆的升程测量
4. The length, diameter and using time of mandril are needed in the process of manufacturing the pipe.
   在扩管生产中，需要实时了解每根顶杆的长度、外径、使用次数等信息。
5. Specially design co-extruding die, merely need to replace core mandril, it may produce solid-wall pipe, solid wall inner helix pipe foamed pipe and foam inner helix pipe.
   ◆特殊设计的共挤模头，只需要换芯棒即可同时生产实壁管、壁内螺旋管、泡管、泡内螺旋管。
6. The maximum stress occurs on the surface of the mandril and small stress occurs on the other part of the mandril.
   芯模的最大应力出现在芯模的浅表层，在周向表面上呈点状分布，而芯模其他部位承受的应力并不是很大。
7. The axial stress on the steel tube which appears on the contact region of the steel tube and mandril is larger than the radial and circumferential stress.
   钢管周向和径向的应力值不大，而轴向应力值较大，最大轴向应力出现在钢管与芯模的接触部位。
8. Study on system time lag determination computer simulation of high elasticity mandril model saw band machine tensile system ( 2)
   高弹性顶杆式带锯机张紧系统时滞确定的计算机仿真研究（2）
9. The Fast Drawing of Mandril in Bending Tube by Using AutoCAD
   用AutoCAD软件对弯管芯棒进行快速图解设计
10. Experimental Study of Axial Tension Member with the Prestressed Concrete Mandril
    配置预应力混凝土芯棒的轴拉构件试验研究
11. The influential factors were analyzed in details, such as error of mandril, setting up error and soon.
    在此基础上，从芯轴误差、齿轮安装误差等几个方面对影响因素进行了详细的分析，并对系统进行了不确定度的评定。
12. In order to increase the critical rotative velocity of transmission shafts, it is necessary to improve the size precision of the transmission shaft tube's two ports. The traditional non mandril reducing diameter technology can not guarantee the manufacturing precision.
    为了提高传动轴临界转速，要求提高传动轴管两端口尺寸精度，若采用传统的无芯棒缩径工艺已无法保证制造精度。
13. An offset surface method was proposed to calculate the discrete mandril's height, whose algorithm was very simple and without the convergence problem which is common to analytical algorithm.
    提出了采用偏移球心曲面计算顶杆高度的方法，算法实现简单，无解析算法产生的收敛问题。
14. It give out an efficient method of saw band machine tensile system lag determination through the analysis of time lag state equation on high elasticity mandril model saw band machine tensile system.
    本文通过对高弹性顶杆式带锯机张紧系统时滞状态方程的分析，得出了确定带锯机张紧系统时滞的有效方法。
15. The writer tried to make full use of the merit of the prestressed concrete and designed prestressed concrete mandril to control crack of structure.
    本文尝试利用预应力混凝土的诸多优点，设计了预应力混凝土芯棒用来控制构件或结构的裂缝。
16. In the present study, we design an automatic remote control system, which is used to push the mandril out of large rocket engine.
    为实现大型火箭发动机中的芯棒与推进剂分离，设计了大型火箭发动机自动顶芯脱模系统。
17. The structure analyse and design of mandril in the thin-wall tube's cool-bending
    薄壁管冷弯成型中芯棒的结构分析及设计
18. This paper brings forward a means of fast drawing of the mandril's structure in bending tube by using AutoCAD.
    介绍了利用AutoCAD软件对管材弯曲工艺中弯管芯棒进行快速图解设计的方法。
19. Effects of mandril position on cold drawing internal rifled tubes
    芯棒位置对冷拔内螺旋凸筋管成型的影响
20. A Design of the Base Pressing Mould of Hydraulic Press Mandril Driving Side Taking Out
    液压机顶出杆驱动侧抽芯动作的底座压制模具设计
21. Study on the application of prestressed mandril in continuously reinforced concrete pavement
    预应力芯棒在连续配筋混凝土路面中的应用
22. The prestressed concrete mandril, which was firstly applied high pressure on a small concrete bar, and then was made in concrete, so it would act as reinforced bar and resist load.
    所谓预应力混凝土芯棒，即将截面不大的混凝土棒先施加程度相当高的预应力，然后再将它浇筑在现浇混凝土中，则它将等效为钢筋起受拉钢筋的作用，与非预应力配筋相近。
23. Analysis for Working Course of Eccentric Mandril Metering Device
    偏心顶杆排种器的工作过程分析
24. Numerical Simulation of Stress-field for Steel Tube Drawing Process with a Short Mandril
    钢管短芯棒拉拔过程应力场的数值模拟
25. The application of prestressed mandril replaced steel reinforcement in continuously reinforced concrete pavement is studied. Material composition and calculation model of prestressed mandril are introduced.
    对预应力芯棒代替钢筋在连续配筋混凝土路面中的应用进行了研究，介绍了预应力芯棒的材料组成和每米宽度路面计算模型。
26. A kind of machining tool for high-rigidity steel rolling and mandril of thimble or oil tube on steel tube product line is developed, it is characterized by its capability of high-rigidity, high wear resistant, high red rigidity and long use life.
    开发研制出一种在钢管加工生产线上高强度轧钢及油、套管芯棒的加工刀具，这种刀具具有高强度、高耐磨性、高红硬性、高寿命的特点。
27. Making and application of adjustable mandril of bed leg
    可调式内芯床腿的制作与应用

noun

1. any of various rotating shafts that serve as axes for larger rotating parts

   Synonym:    spindlemandrelarbor